
Pages: [1] 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 ... 154 Go Down |
|
Subject | Started by | Replies | Views | Last post ![]() |
|||
0 Members and 23 Guests are viewing this board. | |||||||
![]() |
![]() |
![]() ![]() Veteran FJ owners have known about this for years, so this is a important message we carry to the newcomers.If you have a 1984 t...
|
Pat Conlon | 3 | 10668 |
![]() by racerrad8 |
|
![]() |
![]() |
![]() Lately it seems that we have been getting questions on which parts are interchangeable between different year FJ's and other mod...
|
Pat Conlon | 10 | 29292 |
![]() by Tor-King |
|
![]() |
![]() |
FJ1200 Fork Rebuild Advice
Hi Guys,I am rebuilding my forks over the winter and found different parts in the forks than is specified in the manual when I t...
|
ajacstern | 14 | 299 |
![]() by FJ_Hooligan |
|
![]() |
![]() |
How would you fix this?
Sorry for the click-bait title. Pictured below is one of the rear mounting holes on the belly-pan / fairing. As you can see, it...
|
duanelr | 9 | 357 |
![]() by giantkiller |
|
![]() |
![]() |
New tire option for 16" rims
I wanted to share some pictures of a new tire that fits on our bike. The Michelin Commander 3 is a new model and it comes in a 1...
|
duanelr | 6 | 467 |
![]() by balky1 |
|
![]() |
![]() |
Fuel leak into crankcase- again.
Pretty simple- the fuel leaks into the crankcase. Ive already had the carbs off and apart. The rubber ends of the needles are st...
|
r.e.wing_fc3s | 7 | 361 |
![]() by Pat Conlon |
|
![]() |
![]() |
Fuel Tank Prep & Coating due to Rust.
Sooo, unexpectedly I am about to embark on cleaning my '85 FJ1100 gas tank.I am doing this based on the condition of my carbs, a...
|
Cat Cracker | 9 | 321 |
![]() by Pat Conlon |
|
![]() |
![]() |
Headlight Lens
« 1 2 3 »
Does anybody know if its possible to separate the headlight glass from reflector and also if its possible to do it without remow...
|
Old Rider | 37 | 3425 |
![]() by FJmonkey |
|
![]() |
![]() |
Front fender mounting tab repair
Another teeball question from this FJ rookie!I unfortunately recently cracked the remaining plastic holding together one of the ...
|
aigram | 8 | 425 |
![]() by andyoutandabout |
|
![]() |
![]() |
FJ1100 fuse cover
« 1 2 »
I lost the fuse cover on one of my 1100's a while back. I tried to make a new cover out of plastifix but having to deposit the p...
|
T Legg | 20 | 1342 |
![]() by T Legg |
|
![]() |
![]() |
The Importance of Working on Your Motorcycle, by Kevin Cameron
« 1 2 3 »
We FJ riders understand this, however, with today’s complex bikes, many motorcyclists do not....Here is a reprint from a 11/30/2...
|
Pat Conlon | 41 | 2412 |
![]() by bcguide |
|
![]() |
![]() |
The little o-ring that ruined my whole week.
I've been rebuilding my 89 FJ engine, and have done all the necessary work in the crankcase, so after doing a few "dry fittings"...
|
laseron | 11 | 613 |
![]() by jono |
|
![]() |
![]() |
No more popping in and out of gear
I finally installed one of RPM's undercut gear transmissions.I also installed a shift detent kit and my son Ian found me an NOS ...
|
T Legg | 9 | 590 |
![]() by T Legg |
|
![]() |
![]() |
Replacing diaphrgam
Her is my road to replacing the carburetor diaphragm . This is a poor mans DIY and of course the quality of the diaphragm i boug...
|
Old Rider | 5 | 545 |
![]() by Old Rider |
|
![]() |
![]() |
Rebuilding the fuel petcock
« 1 2 »
After using a small crescent wrench to switch the 35 year old Petcock from prime to on (on the new to me fj1100 I just bought )...
|
T Legg | 23 | 3927 |
![]() by T Legg |
|
![]() |
![]() |
Crankshaft bearing sizing
I've been rebuilding my 89 FJ with 100,000 miles on the clock. I'm about to replace the crank main bearings, and have a question...
|
laseron | 3 | 333 |
![]() by Old Rider |
|
![]() |
![]() |
FJ1100 mixture screw
Can anyone tell me what the factory setting is for turns out for the mixture screws. And, how to get rid of this icon?Thanks...
|
kawonda750 | 14 | 980 |
![]() by Waiex191 |
|
![]() |
![]() |
Fuel tank winterization
It's that horrible time of year where the bike gets put away for 6 months due to Wisconsin winter.I'm removing the fuel tank thi...
|
aigram | 13 | 996 |
![]() by Ted Schefelbein |
|
![]() |
![]() |
Oil pump gear assembly sequence
I know I'm the one who has stuffed this up, but, in reassembling my oil pump and refitting, I've found a weird difference betwe...
|
Troyskie | 2 | 285 |
![]() by Troyskie |
|
![]() |
![]() |
propping up front end
« 1 2 »
Dumb question #99. I am getting new tires so am taking off the wheels to bring them in. To prop up the front, can I use my floo...
|
kawonda750 | 28 | 2039 |
![]() by T Legg |
Pages: [1] 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 ... 154 Go Up |
|
![]() ![]() ![]() ![]() |
![]() ![]() ![]() |
Powered by SMF 1.1.10 :: SMF © 2006-2009, Simple Machines LLC
Your membership helps support the hosting costs of the forum |
|