Maintenance

Pages: 1 2 3 4 5 6 7 [8] 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 ... 153 Go Down

	Subject	Started by		Replies	Views	Last post
0 Members and 22 Guests are viewing this board.
	1990 FJ1200 Vibs hi all ,,I have a 1990 FJ1200 , Done all the normal FJ Mods ,,plus New Plugs ,Set Mixtures, Balanced Carbs ,the Bike starts and...		wainot-Phil	0	358	August 30, 2019, 08:15:13 AM by wainot-Phil
	SYNC PROBLEM Howdy folks I have 3 Mikunis in a row that fit a Yamaha of mine. I understand a carb sync on these old carbs will only last a c...		chiz	8	880	August 29, 2019, 07:08:14 AM by JMR
	Alternator Hello. Last week I removed the alternator for some maintenance and I saw a hole next to the flange mounting bolt hole that goes ...		Starquest	14	1543	August 25, 2019, 05:56:52 AM by Starquest
	1989 3cv FJ1200 overheating? hi alljust back to the FJ fold with a new purchase, an '89 3cv with 30k milesthe bike runs well but appears to be overheating (6...		ally	7	807	August 24, 2019, 03:07:55 PM by ELIMINATOR
	Pulling the shift shaft seal I need to get that replaced soon. I'm pretty sure I can get by with my normal bag of tricks, but is there something specific tha...		JPaganel	4	698	August 23, 2019, 07:19:07 PM by JPaganel
	Rear brake / master cylinder problem after attempting fluid change 1987 FJ1200. I was changing out fluids the other day and ran into a problem with the rear brake. The clutch and front brake flui...		vandy	5	1794	August 23, 2019, 12:38:30 PM by vandy
	Putting in new riser bars and right 8mm hex barend is seized « 1 2 ... 5 6 » i have no torchi have no impact hammeri scratched it with an inner-tube and vise gripthe hex is a little roundedwhat is the answ...		mtc	83	16098	August 14, 2019, 01:59:44 AM by mtc
	Removing exhaust silencers I have a '91 ABS model. The rear cans are held on by button Allen key (6mm) bolts that go through a bracket to a threaded, slidi...		Hoppity	4	1483	August 08, 2019, 06:56:54 PM by Tuned forks
	Intake Manifold O rings Hi all, does anyone know off hand the size of the inlet manifold O rings? I've got the old ones for a sample but good to know wh...		Relick	3	562	August 07, 2019, 04:26:20 PM by FJ_Hooligan
	Removing Valve guides When removing Valve guides do you drive them from the port side or spring end. Cheers		roverfj1200	1	416	August 06, 2019, 09:52:22 AM by JMR
	Another bad Kreem job « 1 2 3 4 » Well, I have a new owner of the FJ that the General had for his 2018 USA adventure. I got the bike all sorted and running. I not...		racerrad8	46	4804	August 01, 2019, 10:54:48 AM by Mike Ramos
	Replacing diaphragm in carbs HiJust to show one way of putting in new diaphragm , I ordered types like the original, so you need a rubber ring and clip (seeg...		TomJK	13	1235	August 01, 2019, 08:59:18 AM by TomJK
	1988 FJ1200 Fr. Brake Master cyl. Got it in bits, cleaned, painted and looking beautiful with the kit waiting to go in.......Anyone got a pick of a correctly asse...		Relick	3	570	July 27, 2019, 10:07:08 PM by Relick
	Carb tuning... I want to make my bike run better. Have a set of sync gauges still not too sure how to properly sync. The gauges are all pretty ...		iridewheelies	8	921	July 23, 2019, 02:05:24 AM by X-Ray
	Chain lubrication « 1 2 » So I hope this doesn't turn into one of those disagreeable subjects like tires and motor oil. Before the WCR, I had asked Rober...		Tuned forks	27	2831	July 22, 2019, 10:21:19 PM by X-Ray
	JIS/JICS screws for master covers I am going to order those screwdrivers from McMaster Carr that one of the members posted a link to. Sorry, I've forgotten who y...		Tuned forks	11	1234	July 18, 2019, 08:58:08 AM by ZOA NOM
	Fixing old coils My old 88 has had some trouble with moisture for a few years now. It would miss and splutter after being washed or in heavy rain...		roverfj1200	3	608	July 14, 2019, 06:29:00 AM by ribbert
	Starting hard... still So my Fj is still have starting difficult. The choke seams to help but I still have to crank it for quite a while and play with ...		Dieselman7.3	5	666	July 14, 2019, 03:12:06 AM by Dieselman7.3
	How do I repair broken Chin Fairing « 1 2 » On a recent trip, my chin fairing which had a small crack has now gone so far so it’s broken now.Do I try to plastic weld it or ...		Sparky84	29	2667	July 11, 2019, 11:00:25 PM by bcguide
	Rpm Fork Valves quick question Hello Randy, Robert and everyone, Just doing a leaking seal replacement on the ‘93 FJ, and after pulling the forks apart, I have...		X-Ray	5	856	July 11, 2019, 05:35:51 PM by X-Ray

Pages: 1 2 3 4 5 6 7 [8] 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 ... 153 Go Up

Topic you have posted in

Normal Topic

Hot Topic (More than 15 replies)

Very Hot Topic (More than 25 replies)

Locked Topic

Sticky Topic

Poll

Jump to:

Your membership helps support the hosting costs of the forum
There are several levels of membership that offers other privileges.
Click here to see the various membership levels.