
Pages: 1 2 3 4 5 6 7 8 [9] 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 ... 154 Go Down |
|
Subject | Started by | Replies | Views | Last post ![]() |
|||
0 Members and 17 Guests are viewing this board. | |||||||
![]() |
![]() |
Alternator
Hello. Last week I removed the alternator for some maintenance and I saw a hole next to the flange mounting bolt hole that goes ...
|
Starquest | 14 | 1981 |
![]() by Starquest |
|
![]() |
![]() |
1989 3cv FJ1200 overheating?
hi alljust back to the FJ fold with a new purchase, an '89 3cv with 30k milesthe bike runs well but appears to be overheating (6...
|
ally | 7 | 1060 |
![]() by ELIMINATOR |
|
![]() |
![]() |
Pulling the shift shaft seal
I need to get that replaced soon. I'm pretty sure I can get by with my normal bag of tricks, but is there something specific tha...
|
JPaganel | 4 | 902 |
![]() by JPaganel |
|
![]() |
![]() |
Rear brake / master cylinder problem after attempting fluid change
1987 FJ1200. I was changing out fluids the other day and ran into a problem with the rear brake. The clutch and front brake flui...
|
vandy | 5 | 2050 |
![]() by vandy |
|
![]() |
![]() |
Putting in new riser bars and right 8mm hex barend is seized
« 1 2 ... 5 6 »
i have no torchi have no impact hammeri scratched it with an inner-tube and vise gripthe hex is a little roundedwhat is the answ...
|
mtc | 83 | 18121 |
![]() by mtc |
|
![]() |
![]() |
Removing exhaust silencers
I have a '91 ABS model. The rear cans are held on by button Allen key (6mm) bolts that go through a bracket to a threaded, slidi...
|
Hoppity | 4 | 1665 |
![]() by Tuned forks |
|
![]() |
![]() |
Intake Manifold O rings
Hi all, does anyone know off hand the size of the inlet manifold O rings? I've got the old ones for a sample but good to know wh...
|
Relick | 3 | 736 |
![]() by FJ_Hooligan |
|
![]() |
![]() |
Removing Valve guides
When removing Valve guides do you drive them from the port side or spring end.
Cheers
|
roverfj1200 | 1 | 558 |
![]() by JMR |
|
![]() |
![]() |
Another bad Kreem job
« 1 2 3 4 »
Well, I have a new owner of the FJ that the General had for his 2018 USA adventure. I got the bike all sorted and running. I not...
|
racerrad8 | 46 | 6252 |
![]() by Mike Ramos |
|
![]() |
![]() |
Replacing diaphragm in carbs
HiJust to show one way of putting in new diaphragm , I ordered types like the original, so you need a rubber ring and clip (seeg...
|
TomJK | 13 | 1603 |
![]() by TomJK |
|
![]() |
![]() |
1988 FJ1200 Fr. Brake Master cyl.
Got it in bits, cleaned, painted and looking beautiful with the kit waiting to go in.......Anyone got a pick of a correctly asse...
|
Relick | 3 | 745 |
![]() by Relick |
|
![]() |
![]() |
Carb tuning...
I want to make my bike run better. Have a set of sync gauges still not too sure how to properly sync. The gauges are all pretty ...
|
iridewheelies | 8 | 1206 |
![]() by X-Ray |
|
![]() |
![]() |
Chain lubrication
« 1 2 »
So I hope this doesn't turn into one of those disagreeable subjects like tires and motor oil. Before the WCR, I had asked Rober...
|
Tuned forks | 27 | 3631 |
![]() by X-Ray |
|
![]() |
![]() |
JIS/JICS screws for master covers
I am going to order those screwdrivers from McMaster Carr that one of the members posted a link to. Sorry, I've forgotten who y...
|
Tuned forks | 11 | 1596 |
![]() by ZOA NOM |
|
![]() |
![]() |
Fixing old coils
My old 88 has had some trouble with moisture for a few years now. It would miss and splutter after being washed or in heavy rain...
|
roverfj1200 | 3 | 785 |
![]() by ribbert |
|
![]() |
![]() |
Starting hard... still
So my Fj is still have starting difficult. The choke seams to help but I still have to crank it for quite a while and play with ...
|
Dieselman7.3 | 5 | 912 |
![]() by Dieselman7.3 |
|
![]() |
![]() |
How do I repair broken Chin Fairing
« 1 2 »
On a recent trip, my chin fairing which had a small crack has now gone so far so it’s broken now.Do I try to plastic weld it or ...
|
Sparky84 | 29 | 3496 |
![]() by bcguide |
|
![]() |
![]() |
Rpm Fork Valves quick question
Hello Randy, Robert and everyone, Just doing a leaking seal replacement on the ‘93 FJ, and after pulling the forks apart, I have...
|
X-Ray | 5 | 1142 |
![]() by X-Ray |
|
![]() |
![]() |
Ugh, clutch slave again.
« 1 2 »
My clutch slave dumped it's guts a while ago. Tore it down, seals looked reasonably sound but the bore and piston looked pretty ...
|
great white | 17 | 2441 |
![]() by RPM - Robert |
|
![]() |
![]() |
Revs reading high
Hi,during a recent ride my FJ again started to bug me again.All of a sudden the tachometer displayed rev readings twice as high ...
|
TJ | 6 | 1331 |
![]() by TJ |
Pages: 1 2 3 4 5 6 7 8 [9] 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 ... 154 Go Up |
|
![]() ![]() ![]() ![]() |
![]() ![]() ![]() |
Powered by SMF 1.1.10 :: SMF © 2006-2009, Simple Machines LLC
Your membership helps support the hosting costs of the forum |
|