Maintenance

Pages: 1 2 3 4 5 6 7 8 9 10 11 [12] 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 ... 153 Go Down

	Subject	Started by		Replies	Views	Last post
0 Members and 19 Guests are viewing this board.
	Only firing on no. 2 and 3 Hello my fellow FJ gurus. On first start up my bike on my gets hot on number 2 and 3 exhaust. It’s also rough on start up for ab...		Scottie1	3	596	March 13, 2019, 07:24:15 AM by balky1
	Float bowl ports Are these ports connected to one another? They look like they ought to be but I get no flow between them, even after about 3 hou...		woodcreekpete	7	746	March 10, 2019, 08:34:56 PM by FJ_Hooligan
	MOVED: Splitting the cases This topic has been moved to FJ Project Writeups. http://www.fjowners.com/index.php?topic=18143.0		racerrad8	0	330	March 10, 2019, 05:54:41 PM by racerrad8
	Right side foot rest Does anyone know how to take off the right side foot rest bracket. I have taken off every not and bolt I can see apart from the ...		Scottie1	2	471	March 07, 2019, 11:41:22 AM by Scottie1
	Like using teflon tape on a compression fitting « 1 2 » I had to pull the headers on my new yellow fj1100 to change the oil.The previous owner put enough silicone on to seal all the wi...		T Legg	16	1507	March 07, 2019, 09:59:11 AM by Old Rider
	Oil in starter motor So.. I seem to get oil in the starter motor. Anyone encountered this?Couple of years ago I did a silly and put too much oil in t...		ScavengerProd	13	1171	March 06, 2019, 04:47:35 PM by ScavengerProd
	My bike used to lean right My black FJ used to lean to the right on the center stand.I didn't mind ,I lean to the right also but I decided to find out why....		T Legg	4	675	March 06, 2019, 12:37:44 PM by great white
	Clearcote on polished alu parts? « 1 2 » I have polished the aluminium on the engine covers what now? im thinking of clearcote them with spraymax 2k .Is that a bad idea...		Old Rider	19	1949	March 05, 2019, 02:34:53 PM by Millietant
	Tire balancing I just finished changing four tires on my two fj's and two on the zzr1200.I've always heard to install the red dot(the lightest ...		T Legg	2	496	February 27, 2019, 07:57:03 PM by T Legg
	Grease degunking OK, so I decided to rebuild an old CB400F I've had in the barn for 15 years. It was originally bought to be a parts bike but wh...		Motofun	8	1111	February 27, 2019, 09:02:25 AM by Paul.1478
	Rear swingarm shroud Sorry - don't know what the actual part is, but see attached pics of perished shroud assembly that is just behind rear shock / s...		WEJ	3	585	February 17, 2019, 04:30:59 PM by Pat Conlon
	Engine overhaul : What to replace ? Hi again. I have to replace the starter clutch on my 1200. If i set the engine apart i want to replace everything thats need to...		Vilike	2	649	February 16, 2019, 09:37:22 AM by Vilike
	Vapor out of the crankcase breather? I recently replaced the stock airbox with RPM Dual Pod's, and have the crankcase breather filter installed as a result of the st...		aigram	13	1563	February 15, 2019, 03:48:56 PM by Pat Conlon
	coils « 1 2 » My bike is having a extremely hard time starting from cold. I have had carbs rebuild tuned up etc. I got a OHM meter and stuck b...		Scottie1	20	2075	February 12, 2019, 05:49:35 PM by Tuned forks
	Carbs problems « 1 2 » Hi! I'm from Spain, fj1200 club. I'm restoring a 1988 FJ1200 3CV. My problems are the carbs and microexplosions from the admisio...		sutantonio	16	1979	February 10, 2019, 04:31:25 PM by sutantonio
	1984 Yamaha fj 1100 « 1 2 3 » I have recently inherited the 84 fj 1100.. Started digging into it to see why it was not running.. Found no compression in any o...		mikedastonfj1100	36	10732	February 06, 2019, 02:20:27 PM by mikedastonfj1100
	WTH? Running last week beautifully. Last week had the '86 up and running beautifully! Everything is clean and new in carbs and were rebuilt correctly. Today, trie...		Tor-King	4	895	February 02, 2019, 10:53:16 AM by Tor-King
	Clutch push rod seal I just replaced my clutch slave cylinder and noticed that I didn’t have the push rod seal on the rod. I have a spare one and I’m...		Scottie1	13	1452	January 25, 2019, 05:27:26 AM by Urban_Legend
	F up? So, I rebuilt my engine for my '86. Things went really well thanks to the help I received from Randy! Installed the engine, ho...		Tor-King	7	790	January 21, 2019, 11:27:08 PM by Tuned forks
	Importance of rubber sheaths in cylinder studs Hi everyone,I'm hoping someone could help me please.I have a '92 fj1200 which has starter clutch trouble so having pulled the mo...		millosman	5	927	January 15, 2019, 07:12:58 AM by CutterBill

Pages: 1 2 3 4 5 6 7 8 9 10 11 [12] 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 ... 153 Go Up

Topic you have posted in

Normal Topic

Hot Topic (More than 15 replies)

Very Hot Topic (More than 25 replies)

Locked Topic

Sticky Topic

Poll

Jump to:

Your membership helps support the hosting costs of the forum
There are several levels of membership that offers other privileges.
Click here to see the various membership levels.