*
  • Home
  • Gallery
  • Help
  • Search
  • Login
  • Register
FJowners.com > General Category > Maintenance
News


Pages: 1 2 [3] 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 ... 154   Go Down
 
Subject Started by Replies Views Last post
0 Members and 22 Guests are viewing this board.
Paint code
The spec tag under my seat is damaged.  Can't remember for sure but is there a paint code on it? Last 2 digits of the vin r 92. ...
twangin4u 0 251 Last post July 28, 2020, 04:59:29 AM
by twangin4u
decarbonization of pistons
I just wanted to pass along how easy it is to decarbon your pistons using Berryman Chem Dip. I'm sure many of you know about thi...
bigbore2 0 313 Last post July 24, 2020, 07:02:27 PM
by bigbore2
looking for a Carb diagnosis confirmation
I finally got the '85 FJ out of hibernation.  It has Pods, a stage 1 kit and a Vance and Hines pipe.  Anyways it runs strong but...
Motofun 5 720 Last post July 22, 2020, 12:23:37 PM
by FJ_Hooligan
SHIM 36Y-22127-00-00
Just wondering if anyone have encountered these shims that go inside the swingarm thrust covers. I only have one shim is it poss...
chiz 3 505 Last post July 17, 2020, 12:59:54 AM
by Pat Conlon
A little tip on polishing the brake rotor bolts
since my brakerotor bolts is 34 years old they tend to rust and get ugly very fast after riding in the rain i needed a fast way ...
Old Rider 1 475 Last post July 14, 2020, 10:06:51 PM
by fj1289
2nd gear issue and solving
hi guys im chuffed to be allowed on this forum,Youve all probably had an issue with the second gear on your bikes ive just had a...
JEFF1970 2 498 Last post July 09, 2020, 12:31:46 PM
by Pat Conlon
Wheel bearings SKF 6302 z
Has anyone tried the SKF 6302 Z bearings on frontwheel i read that they are for washing machines but skf is top quality.I tried ...
Old Rider 12 1383 Last post July 07, 2020, 02:55:17 AM
by balky1
Dry Erase Maintenance Chart
At the present time, I don't have my own garage to do routine and elective maintenance. My friend Roger has a detached garage in...
aviationfred 1 430 Last post June 30, 2020, 06:34:26 PM
by X-Ray
85 fj throttle cable issue
I think I have to replace the 2 upper throttle cables.the problem I am having is splitting the housing,one of the 3 screws is be...
bruce j 6 854 Last post June 28, 2020, 08:53:09 PM
by andyoutandabout
Fuel petcock rebuild kit FJ1200 vs XJR 1300
I have developed a fuelpetcock airleak on my 1986  FJ1200 1TX .When i do the sucktest on vacuumehose there is no vacuum air goes...
Old Rider 1 474 Last post June 26, 2020, 09:50:16 AM
by Old Rider
4° advance
Did the ignition advance about a month ago and pleased with results.  Always been a little unsure of the exact degree I was at t...
twangin4u 0 454 Last post June 22, 2020, 02:36:45 PM
by twangin4u
my 1991 FJ 1200
HI To everyone i am new ere need help on servicing my FJ1200 1991 just got it thanks
FURMAN45 1 435 Last post June 21, 2020, 08:53:29 PM
by CutterBill
Cylinder head bolt replacemant
I’m making a cylinder rebuild of my FJ1200 3CW 1990 because it consumed a lot of oil.Wheel dissembling I have seen that all the ...
nathan64 2 481 Last post June 21, 2020, 10:23:57 AM
by RPM - Robert
Front sprocket shaft oil seal replacement
There's a leak from the front sprocket shaft oil seal. I tried to replace the seal like I do with regular seal  with no success....
stou 11 1132 Last post June 20, 2020, 09:53:27 PM
by racerrad8
Time for Brake and Clutch Overhaul
Last week I got my 90 1200 out to go for a ride and found the clutch master had no pressure. I put it away and took the 1100 ins...
krusty 1 493 Last post June 16, 2020, 10:14:01 PM
by krusty
Caliper bridge bolt torque value?
All,I split my calipers for a rebuild and my service manual doesn't have torque values for the bridge bolts.  These are the 4 al...
Waiex191 4 811 Last post June 09, 2020, 01:04:17 PM
by Waiex191
Valve hanging open UPDATE
Back again  Several months ago I started a discussion about being puzzled why, after doing a shim job that one intake valve fart...
chiz 5 796 Last post June 09, 2020, 11:58:32 AM
by chiz
Front Cam Chain Guide Height
Does this look like the right height for the guide to be sticking up past the surface. It's about 3.5mm proud. Had everything ba...
woodcreekpete 6 765 Last post June 07, 2020, 04:25:59 PM
by woodcreekpete
Brake Rotor Minimum Thickness(es)?
Anyone know the minimum brake rotor thicknesses for our bikes, off the top of their head?Don't happen to have my shop manual her...
Steve_in_Florida 4 2161 Last post June 04, 2020, 11:16:47 AM
by XEAGLKPR
Swingarm bearing removal « 1 2 »
I tried the google search around here for anything specific to replacing the swingarm bearings, but all I found was about the li...
Troyskie 17 1848 Last post June 04, 2020, 04:24:14 AM
by Sparky84
Pages: 1 2 [3] 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 ... 154   Go Up
 

Topic you have posted in
Normal Topic
Hot Topic (More than 15 replies)
Very Hot Topic (More than 25 replies)
Locked Topic
Sticky Topic
Poll
:  
Powered by SMF 1.1.10 :: SMF © 2006-2009, Simple Machines LLC

Your membership helps support the hosting costs of the forum
There are several levels of membership that offers other privileges.
Click here to see the various membership levels.

 
 

Loading...