*
  • Home
  • Gallery
  • Help
  • Search
  • Login
  • Register
FJowners.com > General Category > FJ Project Writeups
News


Pages: 1 2 [3] 4 5 6 7 8 9 10 11   Go Down
 
Subject Started by Replies Views Last post
1 Member and 7 Guests are viewing this board.
Timing chain
93000 miles re shimmed valve's should i replace oem chain tensioner 1986 fj1200 still runs pretty good,but cam chain is a little...
vettman 9 1833 Last post May 12, 2019, 09:17:53 PM
by Flynt
1987 FJ 1200 Cafe/Street Fighter project!
Hello hello!I just picked up a 1987 FJ 1200 in well taken care of stock condition after 10+ years of being without a motorcycle ...
dlearyous 1 1081 Last post May 10, 2019, 11:46:49 AM
by Mixed
Young 1990 FJ1200 Owner Facing a LONG build
HARD TO ADMIT A MISTAKE... I ABUSED THE HELL OUT OF THE 1990 FJ1200 AND LEFT IT TO ROT FOR A YEAR IN PIECES AND IN THE ELEMENTS ...
spyy.vs.spii 2 1319 Last post February 19, 2019, 05:15:43 PM
by racerrad8
Repair of the Christmas roasted FJ « 1 2 3 4 »
I have begun the repairs on my FJ that caught fire during my vacation to South Carolina and Florida. The carbs are on their way ...
aviationfred 52 8568 Last post February 10, 2019, 02:06:57 PM
by racerrad8
FJ1200 ABS '91 from damp shed - Moditus attack story « 1 2 »
It was September 2014 when I decided that I will buy my first Yamaha.She was in pretty bad condition: rust, dust and spider webs...
MOTOMYSZOR 24 10961 Last post December 14, 2018, 03:17:11 PM
by MOTOMYSZOR
Header Paint
The headers on my 89 are just about covered in rust and sooner or later they're going to grow some holes so I figured I'[d bette...
RobbieKNobbie 9 2548 Last post October 31, 2018, 02:58:02 PM
by Troyskie
'90 FJ1200 « 1 2 »
Hi guys I'm gonna start my build thread here so it's not in the intro section.So far:+Oil filter change (w/ 2 o-rings), Rotella ...
sekter1 21 6128 Last post October 01, 2018, 12:08:43 PM
by sekter1
My '89 3CV spruce-up
After over 20 years of service, in early 2010 I decided it was time to give my FJ1200 a spruce up and to replace/upgrade a few b...
Millietant 11 3162 Last post September 27, 2018, 01:57:56 PM
by Millietant
Sparkles version 2.0 « 1 2 3 »
Hey all. A week or two ago I put a post about how a 1 hour job to replace the intake boots had escalated into something so much ...
Urban_Legend 44 10637 Last post September 23, 2018, 03:51:15 AM
by Troyskie
This winter's project
I started on this bike back in October. I made a lot of progress, but now I am in a lull waiting for the painter to schedule tim...
chrism40 13 4157 Last post September 22, 2018, 12:43:12 PM
by Tuned forks
My 85 fj
Been wanting one forever as always liked the looks of them. Finally found one in my price range on Craigslist a few years back. ...
Kgip2k 11 3176 Last post July 19, 2018, 10:32:26 PM
by Pat Conlon
Resurrecting my '92 « 1 2 »
Hello, I think I posted this in the right place...Its time to post up some progress on my 1992 FJ1200.  I introduced my self her...
enbruchman 19 4422 Last post June 27, 2018, 08:26:14 PM
by enbruchman
West Coast,RSA summer project « 1 2 3 4 5 »
Hi allThis afternoon I started to strip the FJ for complete paint job and few machanical stuff like clutch,carbs,valve clearence...
aj52 70 17291 Last post June 25, 2018, 03:19:23 PM
by aj52
Long term rebuild
Well, I finally figured out how to wrench and ride at the same time. Got me a 2017 V-Strome 650 so that I can do some proper wor...
Bob 0 928 Last post June 24, 2018, 06:41:15 AM
by Bob
Slightly modified '84 Fj1100
Nearly there. Off for exhausts. Very low.
Indiana jones 12 4345 Last post May 30, 2018, 01:23:33 PM
by Indiana jones
FJ1100 converted to naked bike look « 1 2 »
Here's my ongoing project. These are the parts i've replaced so far. Front and rear tires6pcs brakeswindscreenheadlight signal l...
fjman 17 7943 Last post May 22, 2018, 11:12:15 PM
by Pat Conlon
Refreshing my engine found this « 1 2 ... 6 7 »
I discovers I have 1219 pistons.also my #4 cylinder sleeve is chipped
Mike m 94 22802 Last post April 21, 2018, 06:48:43 PM
by aviationfred
FZ1 Swing Arm Install « 1 2 »
Installation of the FZ1/Fazer swing arm is being done. So far all is going ok. Preliminarily everything looks like it will line ...
aviationfred 27 6346 Last post April 11, 2018, 07:54:05 PM
by aviationfred
Upside Down Forks Part II « 1 2 »
This project actually started the day back in August that I purchased this FJ. I contacted Dan (giantkiller) about a set of fork...
aviationfred 21 4542 Last post March 25, 2018, 02:42:44 PM
by aviationfred
1990 FJ12 Rebuild in Ireland « 1 2 3 »
Hi folks,Hope you all having a good break over Christmas.I am down with bad flu and stomach bug. Just able to get at the laptop ...
Mypoorfudge 41 8595 Last post March 14, 2018, 02:52:00 AM
by Mypoorfudge
Pages: 1 2 [3] 4 5 6 7 8 9 10 11   Go Up
 

Topic you have posted in
Normal Topic
Hot Topic (More than 15 replies)
Very Hot Topic (More than 25 replies)
Locked Topic
Sticky Topic
Poll
:  
Powered by SMF 1.1.10 :: SMF © 2006-2009, Simple Machines LLC

Your membership helps support the hosting costs of the forum
There are several levels of membership that offers other privileges.
Click here to see the various membership levels.

 
 

Loading...